Get Answer on How to Reset Rockspace WiFi Extender

 If you are living in the bigger area where the wireless transmission is required then Rockspace WiFi extender is best for you as it helps in boosting the internet signals to the longer extent and in dead zones areas. Re.rockspace.local is a local WiFi extender which works on 2.4 band and gives the full signal with a transmission speed of 300 Mbps. It works at double band and lifts the home organization by increasing the range and speed of the WiFi signals. Before using the full functionality and features of the Rockspace extender, you need to access the basic settings of the extender by accessing the re.rockspace.local. Many times the users complain that they face difficulty with their Rockspace extender. If you are one of them and facing the same problem, the simplest solution of the problem that you can perform to resolve the issue is reset rockspace wifi extender. In this blog, we have described the troubleshooting tips for Rackspace WiFi range extender. 


Troubleshooting Tips to Resolve Different Issues with Rockspace WiFi Extender 

Unable to Access the re.rockspace.local login page 

If you are unable to access the Rockspace extender login page then there could be various reasons behind it such as incorrect web address, wrong IP settings, not connected to the extender network. Here are the tips to resolve the issue: 

  • Make sure that your device is connected to the extender network properly. In case you are using the wired connection then you need to check the connections at the port ends. 

  • Ensure that the cables that you are using are not broken or damaged. If you find any damaged cable then replace it immediately with a new one. 

  • If you are connected to the devices wirelessly then ensure that you have connected to the correct wireless network. 

  • Use the correct web address for accessing the login page of the Rockspace WiFi extender. 

  • If re.rockspace.local web address does not work for you then use the IP address 192.168.0.254. 

  • If the IP setting is creating the issue with the Rockspace login page access then you need to recheck whether your device has been able to obtain the IP address dynamically. You need to adjust the DHCP settings according to the setup process. 

                                         


Outdated Firmware Issues 

The extender firmware is known as the backbone of the networking device. So, it is important that the firmware is updated. It helps to ensure that your device is secure and the performance is not affected by it. Follow the below steps to update the extender firmware:

  • The first step is to login to Rockspace WiFi extender setup wizard and then go to the device administration page.

  • Click on the Check for update button under the firmware update section. If there is any update available then your device will display a notification. Tap on the Update Firmware button to start the updation process.

  • The status of the firmware update will be displayed on the screen. Once the firmware file is downloaded, installation will start automatically. 



Steps to Reset Rockspace WiFi Extender

If you are facing the issues continuously with the Rockspace WiFi extender then reset your extender to the factory default settings. The reset of the device will delete all the customized settings made by you. Here are the steps that you need to follow to reset Rockspace WiFi Extender:

Step 1: The first step is to search for the reset button located at the rear panel or at the bottom of the Rockspace WiFi range extender. 

Step 2: Once you find the reset button then press and hold it for 10 seconds until the LED power light on the front panel starts blinking. 

Step 3: Release the reset button and wait for some time until your device will boot back up.

Step 4: When the reet process is completed then go ahead with the reconfiguration process. 


With the help of the above steps you can reset rockspace wifi extender and make your device workable mode again. One thing that you need to remember is that reset of the Rockspace WiFi extender will delete all the customized settings made by you.



Comments

Post a Comment

Popular posts from this blog

Fascinating User Guide for Re.rockspace.local Setup Using the Web Interface

Image
  With so much development in the technology, several updates have been made in the extender that makes it better than before. Rockspace WiFi range extender is one of the ultimate extenders that comes with various models and speed. It is the device that helps you in extending the existing WiFi network and increase the WiFi range in the host WiFi network where they can’t reach. If you already purchased a Rockspace WiFi range extender and are looking for a simple user manual guide to setup your extender using re.rockspace.local without any network glitch then this blog will be helpful for you. There are two ways to set up the Rockspace WiFi range extender i.e. web interface and WPS button. In both ways, you need to be available physically near the local Rockspace signal booster to connect the existing host WiFi network. Let’s keep reading and know the steps to rockspace setup .  Guidelines for Rockspace Range Extender Setup Using Web Interface  For Rockspace WiFi range extender setup, y
Read more

Ultimate Guide for Users for Rockspace Extender Setup

Image
  Want to configure your Rockspace extender according to your desire? Well, after Rockspace extender setup , you can easily log into your extender and can make the changes into it depending on your needs. If you don’t know how to set up and login into your Rockspace range extender then this blog will help you. In this blog, we have discussed the simple and easiest guidelines on how to perform Rockspace Range Extender Setup on your device and login with the existing WiFi network. Scroll down and check out the steps to login to the Rockspace extender without facing any error.  Instructions for Rockspace Extender Setup Using the Ethernet Cable Look at the below instructions for setting up the Rockspace WiFi range extender using the Ethernet cable: Step 1: The first step is to connect the Rockspace WiFi extender to your computer or laptop using the Ethernet cable. Step 2: After that, launch the internet browser from your system. Thereafter, enter the login address of the Rockspace range e
Read more

How Do I Access the Rock Space WiFi Extender Setup Settings?

Image
  Rockspace WiFi range extender is the amazing device used to store the settings on which you can access the home WiFi network. So, if you want to change the settings of the Rockspace extender then access the re.rockspace.local web address. Thereafter, rename the WiFi network, alter the admin password of the Rockspace extender and adjust the security according to the requirement. Here, you can also create the guest WiFi network and set or replace the other security options. But most of the users are confused about how to do the extender settings. If you are the one who is also looking for the instructions to change or modify the r ock space wifi extender setup settings then don’t panic! You just need to scroll down till the end and check out the steps as mentioned in it. Let’s get started without any further delay.  Instructions for Rock Space WiFi Extender Setup  Go through the below mentioned instructions for the Rockspace WiFi range extender setup: Step 1 : Once you get the IP add
Read more